1. Carving lines. The grooving pattern of lines with equal intensity throughout the disc.
2. Carving low relief. A carved image, raised floor flat sheets of wood a little same lines.
3. Been carved up. A carved image, rising almost completely full. Resolution over low relief.
4. The carved images floating. Wood carving is a 3D appearance visible sides.
Procedures, and how to carve wood.
1. Determine the form and pattern. Design or customize the layout and design is a critical first step in the design. Be known for carving the design. And to recognize the nature of the wood to be used, such as carved wood or ply wood back to back garden. These sculptors must learn and carvings must be the actual.
2. The modeled pattern onto the wood floor. The model is designed to seal on the timber. Or be hammered bolts cardboard master the guitar. Pattern laid out on the floor and bring the face paint with glue. Or starch paste as a compress, then slapped with white chalk or dust all over. Then the paper prototype out Patterns on the wood surface appear.
3. dummy stirrup forming. Is to cut wood carving tools with carpentry tools on it. Then remove the unwanted wood carving wood has a shape close. Comparable to the model in order to achieve the desired shape. Be clear in order to be carved next step in the stirrup visual images, such as lamb or mutton, floating like a crown of Naga, Garuda, and various animal puppets stirrup work to be as close to the picture.
4. The engraving Is to use a sharp chisel. The size and face of the chisel such as acne, curved front and hammer wood carving tools. To cause a pattern which requires wooden hammer to hammer and chisel to dig. The cut and carved designs evoke the beauty of the required form.
Digging the chisel is hammered draw. Using a chisel to fit the perimeter of the pattern. To copy the entire pattern of the lamp by the hammer strike. Hammer time is the right weight. Regularly to a sharp chisel to sink deeper in the same match, then the acne. This is not an area dug out first. Shallow excavation dug before the first layer if the ground was not deep enough, it popped again, and then dig further to get the spacing airy. To bring the carvings to decorate the high ground, they had to dig deep enough I will have to look very far to see the sheep, after digging up the ground and then raised sheep. The pattern of nested layers to reveal a clear pattern lamp. Which intervene in the foothills of the tie to adjust the height of each layer is 1 - 2 - 3 sheep Rae began hammering the chisel carved pattern within the pattern of the profile. It is used to wipe the gouge carved pattern Rae kept up the profile.
The pattern observed in the time slice or slice Rae Rae Lamb design. Technicians need to look at the grain of the wood or chisel to scrape it along. Of the wood Burr is not dating or garden pathway of wood. It will not be so loose and chipped easily. The cut pattern Rae Is to chisel open one last tilt one side and then the wood is cut to the low altitude, not always. To cause shadows in design and clearly visible to the desired format.
This can be done 3 ways to slice.
- Milling pattern spoon
- Lines stretched milling The middle line is stretched
- Milling deleted after this (minus the melon seed).
Tools used in carving.
- Commonly used in wood carvings including teak wood is not too hard. There are beautiful wood Engraving can easily shrink a little longer to weathering and safe from termite and insect popular wood is inferior to pine wood Mok The key is not to be used to make carvings. Be perfect It will work, the lack of a mallet, a hammer that looks like a small mallet. Made of hardwoods such as rosewood rosewood.
- Mallet are lightweight and do not take much effort and time to help maintain long-handled chisel to work with.
- Acne is the most important tool in many types of carving chisel set chisel chisel digging knit gouge chisel made of steel, hardened and tough. The key is to be sharpened regularly.
- A knife is a small knife or small sharp carving the sheep furrows.
- Sawing the lumber unwanted parts away. Up to forming the structure of the work.
- Slug or filings to rub decorative pieces in the carving process then.
- After finishing machine polishing sandpaper to carve it.
- Plane used to smooth wood shavings prior to sheep or other decoration later.
- Drill a hole in wood carving or wood.
- Mount or wild crows, wood handle with wood grip.
- Assembly tools include the ruler, pencils, tracing paper, cardboard do.
- Rochelle materials including chalk, lacquer thinner or linseed oil traded paint for wood.
